FCC Declaration of Conformity Statement
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause interference to radio or television
reception, which can be determined by turning the equipment off
and then on, the user is encouraged to try to correct the interference
by one or more of the following measures:
•
Increase the separation between the equipment and receiver.
•
Connect the equipment to a different outlet so that the equipment
and receiver are on different branch circuits.
•
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by JBL could void
the user’s authority to operate the equipment.
Please Read the Following Operation Precautions Before Use
•
Read instructions – All safety and operating instructions should be
read thoroughly before attempting to operate this audio system.
•
Retain instructions for future reference.
•
Heed warnings – All warnings on this audio system and in the
operating instructions should be adhered to.
•
Follow instructions– All operating and use instructions should
be followed.
•
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER (OR BACK). THERE ARE NO USER
SERVICEABLE PARTS INSIDE THIS UNIT, PLEASE REFER
SERVICING TO QUALIFIED JBL CORPORATION SERVICE
PERSONNEL.
•
Do not expose the speakers to liquid or solvent.
•
Never remove grille covers in order to service the speaker
system. The speaker system does not contain any user serviceable
parts. Refer all servicing to the JBL Technical Support Group.
•
Do not expose the speaker system to temperature or humidity
extremes, direct sunlight, excessive dust, or vibrations.
•
Place the speaker system on a stable, level surface. Do not drop,
apply excessive force to the controls, or put heavy objects on top
of the speaker.
•
If cleaning is required, use a soft dry cloth. If necessary, use a damp
cloth without any solvents.
•
In order to protect the speaker system, avoid microphone feedback,
continuous output from electronic musical instruments, or distorted
output from any signal source.
•
Do not place the speakers close to fluorescent light sources, or neon
light fixtures.
•
Although the speakers are magnetically shielded, keep magnetic storage
media (disks and tapes) at least four inches from the speaker system
in order to avoid data loss.
•
WARNING: To reduce the risk of fire or electric shock, do not expose
this speaker system to rain or moisture.
Step 1. Unpack on tour, wall adaptor and cable. Read this instruction sheet completely.
Step 2. Open battery compartment by sliding button as shown. Battery door will open.
To locate the battery door release and the door itself, follow these
directions.
Locate the three rubber feet on the bottom of the unit. There are two long ones
and a short one in the middle. Place the unit on its top with the three feet at
the front and facing up. The short strip in the middle is the battery door release.
Slide the release to the side. With a fingernail feel just below it and toward you.
You should be able to feel a crack. Just pull toward you with the release still
held to the side. The whole side of the unit will come open.
Step 3. Place (4) fresh AAA batteries as shown. Replace battery compartment cover. System will function with AC power only or batteries.
Step 4. Open protective cover by sliding cover as shown. When the cover is closed, the system will power off.
Step 5. Connect wall adaptor to on
tour. Connect adaptor to wall outlet.
CAUTION - Remove Adaptor from outlet
before installing or replacing batteries.
Step 6. Plug input cable into on tour. Plug input cable to audio device. Start audio device.
Step 7.Adjust Volume using “+” to increase and “-” to decrease. Press both to Mute the on tour Press either button to Unmute.
Step 8. Green LED indicates that power is on. Flashing Green LED indicates no input signal. Amber LED will flash when batteries need replacement.
Created on ... September 23, 2007